Mts Model 512-01 Hydraulic Power Unit Manuale Utente

Model 512.01 Hydraulic Power UnitProduct Information Manual015-206-301 A

Model 512.01 Hydraulic Power Unit 10 Introduction Specifications Model 512.01 SpecificationsP ARAMETER S PECIFICATION EnvironmentalOperating temperatu

Model 512.01 Hydraulic Power Unit Introduction 11 Dimensions The following figure shows those dimensions which are useful when installing the HPU.l563

Model 512.01 Hydraulic Power Unit 12 Introduction

Model 512.01 Hydraulic Power Unit Installation 13 Installation This section describes how to install the Model 512.01 Hydraulic Power Unit (HPU). The

Model 512.01 Hydraulic Power Unit 14 Installation 1. Position the hydraulic power unit. You should determine where to put the hydraulic power unit (H

Model 512.01 Hydraulic Power Unit Installation 15 4. Test the HPU. A. Remove the 1/2” NPT pipe plug and install the breather in the reservoir cover.B

Model 512.01 Hydraulic Power Unit16Installation

Model 512.01 Hydraulic Power Unit Operation17OperationThe following procedure is a guideline, and it assumes you are starting the hydraulic power unit

Model 512.01 Hydraulic Power Unit18Operation5. Check to make sure the filter change gage’s needle stays in the green zone.NOTE Cold fluid may push it t

Model 512.01 Hydraulic Power Unit Maintenance19MaintenanceContents Reducing the Fluid Temperature 20Resetting the Thermal Overloads 22Adjusting

Copyright information © 2000 MTS Systems Corporation. All rights reserved.Trademark information MTS is a registered trademark of MTS Systems Corporati

Model 512.01 Hydraulic Power Unit20MaintenanceReducing the Fluid Temperature The hydraulic power unit (HPU) will be shut down if the hydraulic fluid re

Model 512.01 Hydraulic Power Unit Maintenance21Adding Hydraulic Fluid1. The hydraulic power unit (HPU) will shut down when fluid drops below the sight

Model 512.01 Hydraulic Power Unit22MaintenanceResetting the Thermal Overloads The thermal overloads of the hydraulic power unit (HPU) can be tripped b

Model 512.01 Hydraulic Power Unit Maintenance23Adjusting the Output PressureThe hydraulic power unit (HPU) comes with its output pressure set at 6.9 M

Model 512.01 Hydraulic Power Unit24MaintenanceChanging the FilterChange the filter whenever the filter change gage’s needle stays in the yellow or red z

Model 512.01 Hydraulic Power Unit Maintenance25Changing the Hydraulic FluidAs part of your regular HPU maintenance, change the hydraulic fluid every 2,

Model 512.01 Hydraulic Power Unit26MaintenanceComponent LocationsSynasol is toxic and flammable.Use the Synasol solvent in a ventalated area and keep i

Model 512.01 Hydraulic Power Unit Maintenance273. Clean the reservoir.A. Unscrew the cover screws attaching the cover plate to the reservoir.B. Attach

Model 512.01 Hydraulic Power Unit Contents 3 Contents Introduction 5 Functional Description 6Component Identification 8Specifications 10Dim

Model 512.01 Hydraulic Power Unit 4 Contents

Model 512.01 Hydraulic Power Unit Introduction 5 Introduction Contents Functional Description 6Component Identification 8Specifications 10 Thi

Model 512.01 Hydraulic Power Unit 6 Introduction Functional Description The hydraulic power unit (HPU) is the mechanical source of high-pressure hydr

Model 512.01 Hydraulic Power Unit Introduction 7 Hydraulicschematic The hydraulic schematic shows how the hydraulic components are connected in the M

Model 512.01 Hydraulic Power Unit 8 Introduction Component Identification This table describes the components shown in the figure called “Component Ide

Model 512.01 Hydraulic Power Unit Introduction 9Component IdentificationlControl BoxSight Glass Pressure GageReservoirFluid ThermometerFilterHeat Exc